CO2 Laser Engraving Machine
Industrial 1300x900 mm flatbed CO2 laser cutting and engraving machine powered by a 100W EFR catalyst-enhanced laser tube. Featuring dual precision linear guide rails, hybrid microstepping drives, high-velocity huff air-assist, and a convertible honeycomb and knife-blade table delivering up to 500 mm/s engraving speeds and 10 mm clean acrylic cutting.
- check_circle Generous 1300 x 900 mm Processing Envelope: Ample work table capacity accommodates full-sized commercial signage sheets and batch nesting.
- check_circle 100W EFR Catalyst Laser Tube: Delivers dependable TEM00 mode beam stability for deep 10 mm vector cuts and fine raster detailing.
- check_circle Dual Linear Guide Rail Motion: Precision-ground linear rails and steel-reinforced timing belts yield 0.01 mm repositioning precision.
- check_circle Up to 500 mm/s Raster Engraving: High-speed scanning system produces crisp photo reproductions, vector text, and fine line etching.
- check_circle Interchangeable Honeycomb & Blade Beds: Dual-surface design optimizes support for both delicate small crafts and heavy sheet goods.
- check_circle Hydraulic Coolant Flow Interlock: Automatically shuts down high-voltage excitation if chiller water circulation is interrupted.
- check_circle Advanced DSP Offline Controller: Ruida/RDWorks compatible with USB flash drive input, layer color coding, and dynamic speed/power tuning.
Industrial Applications
Target Production & Material Use CasesVector cutting 2 mm to 10 mm cast and extruded acrylic with mirror-polished transparent edges for backlit channel letters, displays, and point-of-sale fixtures.
Intricate fretwork, architectural scale models, decorative wall panels, wooden gift packaging, and wooden temple partitions with minimal kerf burn.
High-velocity perforation, pattern tracing, and contour cutting of genuine leather, artificial leather (PU/PVC), felt, denim, and synthetic fabrics.
Permanently engraving phenolic double-color sheets, rubber printing plates, coated anodized plates, stone plaques, and precision control panels.
Deep raster 3D relief engraving and vector profiling on bamboo, crystal, jade, granite plaques, glass drinkware, and resin castings.
Key Operational Advantages
Engineering ROI & ReliabilityHigh-density TEM00 laser focus leaves cast acrylic edges crystal clear and glossy right out of the machine, completely removing the need for flame or buff polishing.
Non-contact thermal cutting process exerts zero physical clamping pressure, eliminating tool dulling, bit breakage, and mechanical distortion.
Process complex curves, razor-sharp inside corners, and microscopic lettering at up to 500 mm/s that would be impossible on traditional rotary routers.
No costly CNC collets, end mills, or specialized cutters required; runs on standard single-phase 220V power with readily available industrial consumables.
CO2 Laser Engraving Machine — Industrial Summary
Heavy-Duty Industrial Flatbed CO2 Laser Engraving & Cutting System (1300x900 mm / 100W)
The Daksh DM-1390 CO2 Laser Engraving Machine is an industrial-grade, versatile flatbed fabrication workstation engineered for high-throughput vector cutting and intricate raster engraving across wide-format non-metallic materials. Built around an expansive 1300 x 900 mm (4.26 x 2.95 ft) active processing area, this machine integrates a 100-Watt catalyst-boosted EFR CO2 glass discharge tube, delivering continuous cutting penetration up to 10 mm on cast acrylic and 8 mm on dense MDF boards with zero taper and glass-smooth flame-polished edges.
Engineered with a stress-relieved, fully welded mild steel chassis, the machine dampens torsional harmonics during high-acceleration raster movements up to 500 mm/s. Motion dynamics are driven by dual precision linear guide rails along both X and Y axes, coupled with steel-cord reinforced polyurethane timing belts and high-torque hybrid stepper motors. This configuration ensures consistent 0.01 mm repositioning accuracy and micro-metric spot placement without skipping steps during prolonged production shifts.
Advanced Mechanical, Optical & Control Engineering Highlights:
- Convertible Dual Worktable Architecture: Ships with both an interchangeable cellular honeycomb bed (ideal for preventing micro-part dropouts and back-reflection on delicate paper, fabric, and thin acrylic) and rigid knife-blade aluminum slats (designed for heavy MDF, thick plywood, and acrylic sheets requiring minimum contact area).
- EFR Catalyst-Enhanced CO2 Resonator: Equipped with a genuine 100W EFR sealed glass laser tube featuring internal catalytic chemical coating, ensuring stable TEM00 Gaussian beam distribution, narrow kerf geometry, and an extended service lifespan without premature wattage drop.
- Coaxial High-Pressure Huff Air-Assist: Integrated pneumatic nozzle routes continuous clean compressed air directly over the 20 mm focal optic to blow away combustible gases, eliminate flame charring on timber kerfs, and safeguard the lens against smoke condensation.
- Digital DSP Offline Control System: Supports direct execution via USB flash drive or high-speed Ethernet connectivity. The color TFT console allows operators to dynamically adjust laser power, head velocity, and layer sequencing directly from the machine panel without halting production.
- Comprehensive Operational Interlocks: Integrated inline hydraulic water-flow sensor halts laser firing instantaneously if chiller coolant velocity drops, protecting the delicate glass resonator from thermal cracking.
- High-Efficiency Centrifugal Fume Extraction: High-volume exhaust blower evacuates vaporized organic resins, acrylic fumes, and particulate matter downward through the chassis draft ducting to keep the workspace clean and safe.
Technical Specifications & Machine Architecture
| Specification | Parameter / Value |
|---|---|
| Model Name / Number | DM-1390 (Daksh 1390) |
| Machine Type | Industrial Flatbed Laser Engraving & Cutting Machine |
| Automation Grade | Semi-Automatic Industrial |
| Brand & Manufacturer | Daksh CAD CAM Private Limited |
| Country of Origin | Made in India |
| Working Table Size (X x Y) | 1300 x 900 mm (4.26 x 2.95 ft) |
| Work Table Surface Type | Convertible Honeycomb Mesh & Aluminum Knife Slats |
| Maximum Cutting Depth | Up to 10 mm (Cast Acrylic), 8 mm (MDF/Wood) |
| Body & Frame Material | Heavy-Duty Reinforced Welded Mild Steel Chassis |
| Laser Tube Technology | Sealed CO2 Glass Discharge Laser Tube (Catalyst Coated) |
| Laser Power Output | 100 W Continuous (115 W Peak Burst) |
| Laser Tube Brand | EFR Laser |
| Cooling System Type | Closed-Loop Water Cooling (Compatible with CW-5000 / CW-5200) |
| Cooling & Safety Protection | Hydraulic Water Flow Sensor Interlock & Thermal Alarms |
| Engraving Speed Range | 1 – 500 mm/s |
| Cutting Speed Range | 1 – 100 mm/s |
| Repositioning Accuracy | ±0.01 mm |
| Drive Motors & Transmission | High-Torque Hybrid Stepper Motors, Timing Belts & Linear Guide Rails |
| Control System & Software | DSP Digital Controller (Ruida / RDWorks Offline Panel) |
| Operating Voltage & Frequency | AC 220V ±10%, 50 Hz, Single Phase |
| Air Assist & Exhaust Equipment | Coaxial High-Pressure Huff Air Nozzle & High-Flow Centrifugal Exhaust Fan |
| Minimum Order Quantity | 1 Piece |
Customer Reviews & Operational Ratings
Genuine evaluations from manufacturing plants, fabrication units, and machine operators across India.
Based on 0 verified client reviews.
No Reviews Yet
Be the first industrial buyer to review this machine or spare part. Your operational feedback assists manufacturing engineers nationwide.
Complementary Industrial CNC Systems
CO2 LASER Cutting & Engraving Machine
High-precision CO2 laser cutting and engraving machine (60W–180W) engineered for clean cutting and fine engraving on acrylic, wood, leather, and glass. Built with durable Leadshine motion, CW water cooling, and versatile bed options up to 1400×1000 mm for signage, crafts, and prototyping.
CO2 Laser Machine
Heavy-duty 100W industrial CO2 laser cutting and engraving workstation with 1300x900 mm bed, high-grade EFR/RECI glass tube, water chiller cooling system, and DSP digital motion control for non-metal fabrication.
CNC Router 1325 Wood Working Machine
Experience precision and power with the CNC Router 1325 Woodworking Machine. Featuring a heavy-duty steel frame and a high-speed 6KW air-cooled spindle, it delivers flawless carving, cutting, and milling for furniture, MDF, acrylic, and more.